24 Hour Service Hotline:0769-22710188 / 13713357162

After the discontinuation of dichloromethane paint removers, what are the alternative solutions for removing paint from enameled wires?

1. Policy Background: Paint removers containing dichloromethane have been clearly regulated

According to the "List of Key Controlled New Pollutants (2023 Edition)" jointly issued by the Ministry of Ecology and Environment and other departments, dichloromethane (CAS number 75-09-2) has been included in the key control list, which clearly states:The production of paint removers containing dichloromethane is prohibited, and this provision has been in effect since March 1, 2023 .

Regarding product limits, the current national standard "Limit for Volatile Organic Compound Content in Cleaning Agents" (GB 38508-2020) stipulates: the total of four halogenated hydrocarbons—dichloromethane, chloroform, etc.—in water-based cleaning agents must not exceed 0.5%, in semi-aqueous cleaning agents not more than 2%, and in organic solvent cleaning agents no more than 20%. 。

In terms of occupational health, the "Occupational Exposure Limits for Hazardous Factors in the Workplace Part 1: Chemical Hazardous Factors" (GBZ 2.1—2019) clearly specifies that the time-weighted average permissible concentration of dichloromethane in workplace air (PC-TWA) is 200 mg/m³, with a critical adverse health effect of carboxyhemoglobinemia and peripheral nervous system damage.

Under the constraints of the above policies and standards, industries such as enameled wire processing and motor manufacturing are gradually replacing paint removal products containing dichloromethane. Combining public academic research with industry-wide technical routes, the mainstream enameled wire paint removal solutions without dichloromethane can be divided into the following four categories.

Mainstream paint removal solutions for Class II and IV without dichloromethane

1. Benzyl-based solvent-based paint removers: mainstream industrial alternatives

Using benzyl alcohol (benzyl alcohol) as the core solvent, combined with flux-aids, activators, and corrosion inhibitors, it is currently the most mature technical route to replace dichloromethane paint removers. In a special study on enameled wire paint removers published in Guangdong Chemical Industry, the School of Chemistry and Chemical Engineering at Hefei University of Technology clearly identified benzyl alcohol as the main solvent for preparing paint removers, and verified its effectiveness in removing polyurethane paint films and its compatibility with copper substrates.

· General attributes: Works at room temperature, with paint removal efficiency at a medium to high level; It still has some volatility. Some commercially available formulas contain ingredients such as N-methylpyrrolidone (NMP), so ingredient compliance must be additionally confirmed during selection.

· Applicable scenarios: small to medium batch enameled wire paint stripping, workpiece rework, and conventional production lines requiring certain paint removal speeds.

2. High-temperature alkaline water-based paint remover: specially designed for high-temperature resistant thick paint films

Using alkaline components such as sodium hydroxide and potassium hydroxide as the main components, combined with surfactants, corrosion inhibitors, chelating agents, etc., it is mostly used under high-temperature conditions and is a classic solution for high-temperature resistant enameled wire paint stripping. Experimental studies published in "Electroplating and Finishing" show that alkaline paint remover can quickly remove polyester and polyimide paints with minimal damage to copper- and nickel-based substrates. For extremely high-temperature resistant coatings such as polyimide, the latest 2025 research in Electroplating and Coating further verifies that the sodium hydroxide composite system can remove the paint layer of high-temperature resistant enameled wire within 12 seconds at 325°C without affecting the mechanical or conductive properties of copper wires.

· General attributes: non-flammable and non-explosive, no organic solvent evaporation, low raw material cost; Conventional formulas require heating to 80-95°C, while high-temperature resistant formulations require higher temperature conditions; Improper control of operation carries the risk of corroding the copper core, making it unsuitable for aluminum wire and other non-alkali substrates.

· Applicable scenarios: Batch paint removal of high-temperature resistant enameled wires and large-diameter thick paint films, professional workshops equipped with heating conditions and standardized operation capabilities.

3. Equipment-compatible environmentally friendly paint solvents: efficient solutions for mass production lines

These products are the BT-103 latent solvent used in the specialized latent dissolution instrument for special paint removal equipment, typically used in conjunction with series resonant enameled wire paint removal machines TB - Eco-friendly cleaning agent ionizes cleaning agent molecules through alternating magnetic fields generated by equipment, promoting polymer chain breakage at the molecular level and achieving paint dissolution.

· Paint removal principle: Relying on the alternating magnetic field generated by a series resonant circuit, the cleaning agent molecules inside the tank become ionized, enhancing penetration and bond breakage on the organic paint film of the enameled wire, thereby achieving paint dissolution.

· Core features: Free of halogenated hydrocarbon solvents such as dichloromethane, the product complies with RoHS 2.0 hazardous substance control requirements and is classified as a non-hazardous material; Fast paint removal speed, compatible with various wire diameters, materials, and temperature resistance grades of enameled wires; minimal residue after paint melting, minimizing corrosion impact on copper core; However, it requires dedicated paint removal equipment and is not suitable for purely manual work.

· Applicable scenarios: mass-produced enameled wire processing, paint removal processes on motor/transformer production lines, enterprises with high requirements for environmental compliance and product yield.

4. Bio-based low-VOC paint remover: high environmental standard scenarios

Using plant-derived solvents such as citrate esters and bioalcohols as core ingredients, based on the principle of similar dissolvency, the paint film is penetrated and swollen by bio-based solvents, combined with mild activating ingredients to achieve paint removal. The review of research progress on environmentally friendly paint removers published in "Electroplating and Finishing" identifies the bio-based solvent series as an important future development direction for environmentally friendly paint removers, clearly specifying their characteristics of low VOCs and low occupational health risks.

· General attributes:Low VOC content, minimal odor, low occupational health risks, and relatively less difficulty in waste liquid disposal; The paint removal rate is relatively slow, procurement costs are relatively high, and the removal effect on high-temperature resistant thick paint films is limited.

· Applicable scenarios: Small-batch paint removal for exporting electronic components and medical/food-grade related products, where high environmental and occupational health standards are required.

3. Standard usage methods and key points for different schemes

1. Soaking method (benzyl alcohol type / suitable for room temperature alkaline water-based)

This is the most commonly used process for batch industrial paint removal, and the operation follows these general standards:

1. Pretreatment: removes oil stains and dust from the surface of the enameled wire to prevent impurities from consuming chemicals and affecting penetration effectiveness;

2. Chemical preparation: Benzyl alcohol paint remover is generally used as a undiluted solution; water-based type is diluted according to the product instructions; Pour the agent into a temperature- and corrosion-resistant soaking tank and adjust the temperature as required (benzyl alcohol type is suitable at room temperature, water-based type usually heated to 80-95°C);

3. Soaking and paint removal: Immerse the end of the enameled wire to be removed into the agent, maintaining the appropriate time according to the thickness and type of paint film. During this time, gently shake the workpiece to accelerate the peeling until the film is completely dissolved or wrinkled and peels off, then remove;

4. Post-processing: After removal, immediately rinse thoroughly with running water. If necessary, use a soft brush to clean off any remaining paint residue. After blowing, proceed to the next step.

Operation tip: It is recommended to cover the soaking tank to reduce evaporation and loss; Regularly filter paint residue in the tank and replenish new chemicals according to concentration changes.

2. Brushing Method (Partial Paint Removal Scene)

Only applicable to low-volatile benzyl alcohol gel paint removers, used for localized rework and paint removal:

1. Use a brush to evenly apply paint remover to the areas to be removed; thickening the coating layer can be appropriately applied to thick paint films;

2. Let it sit for 3-10 minutes (extend appropriately if ambient temperature is low), allowing the paint film to fully wrinkle and soften;

3. Use a scraper or brush to remove the dissolved paint film, then rinse thoroughly with clean water.

Operation tip: For vertical surface construction, prioritize gel-type use to avoid chemical flow; Operate the entire process in a ventilated environment, wearing protective gloves and goggles.

3. Equipment is equipped with ionized paint dissolution method

Taking the series resonant paint stripper + supporting eco-friendly cleaning agent as an example, the standard operating procedure is:

1. Add the matching eco-friendly cleaning agent to the specified liquid level into the equipment tank, connect the equipment power, and complete preheating according to the manual;

2. Set corresponding paint removal parameters (current, working time) according to the wire diameter and paint film type of the enameled wire;

3. Place the end of the enameled wire to be removed into the equipment work area, start the equipment to finish melting the paint, and with conventional wire diameters, it usually takes from a few seconds to over ten seconds;

4. Remove the workpiece and rinse off any surface residue with clean water.

4. Key considerations for selection and use

1. Compliance should not be judged solely by "chloroform-free": Some products do not contain dichloromethane but may contain other regulated substances such as chloroethylene and NMP, Confirm full component risk in conjunction with compliance requirements of the product's industry (such as environmental impact assessments and export regulations).

2. Must be tested on a small scale before mass production: The compatibility varies greatly depending on different paint film types, wire diameters, and materials. Before formal purchase, it is recommended to test the paint removal effect, substrate corrosion, and subsequent welding performance with samples. Only after confirming everything is correct before mass use.

3. Temperature is the core variable affecting efficiency: Most paint removal agents without DCM paint removal agents have a significant rate of increased paint removal with rising temperature. In low-temperature environments, it is recommended to increase heating appropriately or extend treatment time.

4. Waste liquid must be disposed of according to regulations: Even environmentally friendly paint removers, the waste liquid after dissolving the paint is considered industrial wastewater and must be treated in compliance with local environmental protection requirements; direct discharge is not allowed.

5. Summary of Scenario Selection

· For those seeking cost-effectiveness, ambient temperature operation, and conventional paint film removal, benzyl alcohol-based solvent-based paint removers are preferred;

· For high-temperature resistant thick paint films with heating equipment, prioritize high-temperature alkaline water-based paint removers;

· Mass production lines, emphasis on environmental protection and yield, existing or planned procurement of paint removal equipment, and selection of compatible environmentally friendly paint solvents;

· High environmental standards, small batch high-end products, choose bio-based low-VOC paint removers.


Content is generated by AI



References

[1] Wang Bainian, Sun Xueqing, Chai Duoli. Study on Waterborne Paint Remover for Polyurethane Copper Enameled Wire [J]. Guangdong Chemical Industry, 2015, 42(05):1-4

[2] Wang Linlin. Research on a paint remover for enameled wire [J]. Electroplating and Finishing, 2014, 36(09):36-39

[3] Song Qilong, Chen Zhixun, Mu Xilong, et al. Research on High-Efficiency Compound Sodium Hydroxide Paint Remover for High-Temperature Resistant Enameled Wire [J]. Electroplating and Coating, 2025, 44 (04):141-145

[4] Hao Lifeng, Jiang Zewen, Zhang Zheyang, et al. Research Progress on Environmentally Friendly Paint Remover [J]. Electroplating and Finishing, 2020, 42(10):17-23


Related Content